Cisco Stacking Cable Guide for Catalyst 9300, 9300L, 9300X, and C9350

The 50 cm stacking cable for a Catalyst 9300 or 9300X is STACK-T1-50CM. The C9350 requires STACK-T1A-50CM. That extra A identifies a different cable family. For a C9300L, read the part number on the rear stack adapter before choosing a cable.

StackWise Cables by Switch Model and Length

Switch or installed adapterStacking technology50 cm1 m3 m
C9300StackWise-480STACK-T1-50CMSTACK-T1-1MSTACK-T1-3M
C9300XStackWise-1TSTACK-T1-50CMSTACK-T1-1MSTACK-T1-3M
C9350StackWise-1.6TSTACK-T1A-50CMSTACK-T1A-1MSTACK-T1A-3M
C9300L with C9300L-STACKStackWise-320STACK-T3-50CMSTACK-T3-1MSTACK-T3-3M
C9300L with C9300L-STACK-AStackWise-320STACK-T3A-50CMSTACK-T3A-1MSTACK-T3A-3M
Cisco’s Catalyst 9300 data sheet and C9350 StackWise accessories guide list these data cables. StackPower uses separate cables for power sharing.

STACK-T1 vs. STACK-T1A

If a rack already has STACK-T1-50CM cables connecting two C9300 switches, replacing both switches with C9350s means replacing both data cables. A purchase order that says only “50 cm Cisco stacking cable” leaves the platform unspecified. For a 50 cm C9350 link, put STACK-T1A-50CM on the order and check the full part number on the packing list.

A trailing equals sign identifies a spare. Cisco lists STACK-T1A-50CM=, STACK-T1A-1M=, and STACK-T1A-3M= as C9350 spares. In each case, the A identifies the cable family and the characters after the final hyphen give its length.

Supported Stack Members and Adapters

C9300 and C9300X use the same Type 1 cables, but the switch models and license levels determine whether they can share a stack and what speed it will run.

Planned combinationCompatibility and bandwidth
Standard C9300 + C9300XSupported at 480 Gbps when the license levels match. Check the IOS XE release and the C9300X stack-speed setting before adding the member.
Higher-scale C9300 + standard C9300 or C9300XUnsupported. The higher-scale models stack only with other higher-scale C9300 members at the same license level.
C9300L + C9300 or C9300XUnsupported. The fixed-uplink C9300L and modular-uplink C9300/C9300X belong to different stacking groups.
C9300L + C9300LMSupported at 320 Gbps with matching license levels. Every link to a C9300LM requires Type 3A adapters and cable.
C9350 + Catalyst 9300 series or Catalyst 3850Unsupported. Build a separate C9350 stack when migrating from either family.
The higher-scale C9300 models are C9300-24UB, C9300-24UXB, and C9300-48UB, including their Network Essentials (-E) and Network Advantage (-A) variants.

Matching C9300L Adapters at Both Ends

C9300L kitAdapters includedDefault cable
C9300L-STACK-KIT2 × C9300L-STACK1 × STACK-T3-50CM
C9300L-STACK-KIT22 × C9300L-STACK-A1 × STACK-T3A-50CM
Cisco introduced Type 3A cable and adapter support in IOS XE Cupertino 17.9.x.

A C9300L ring can contain both Type 3 and Type 3A links. The pairing rule applies to each individual cable. For example, to replace a failed Type 3 link with Kit2, change the adapter at each end of that link and install the Type 3A cable. The other working links can continue using their existing Type 3 hardware.

Ordering a Two-Switch Stack

For a full ring, count two cables. One connects Stack 1 on the first switch to Stack 2 on the second. The return cable connects the two remaining ports. On a C9300L pair, all four ports need adapters. The C9350 has built-in StackWise ports.

Example orderSwitchesHardware for a full ring with two 50 cm paths
Fixed-uplink C9300L2 × C9300L-24T-4G-E2 × C9300L-STACK-KIT2. Together the kits supply four adapters and two STACK-T3A-50CM cables.
C93502 × C9350-24TSelect 2 × STACK-T1A-50CM on the switch order. No separate stack adapters are required.
Cisco’s September 2026 C9350 ordering guide lists data stacking cables as selectable accessories. Check the quantities on the quote.

Measuring the Return Cable

Measure each run between the rear ports, following the route through the cable manager. Allow room for the connectors, bends, and service slack. If the resulting paths measure 45 cm and 75 cm, a C9350 pair needs one STACK-T1A-50CM and one STACK-T1A-1M. For the same layout with C9300L Kit2, specify one 1 m Type 3A cable in place of the second kit’s default 50 cm cable.

When expanding an existing 9300 stack, compare the exact member PID and license level with the models listed under Cisco Catalyst 9300 switches.

FAQ

What stacking cable does the Cisco C9350 use?

The C9350 uses STACK-T1A for StackWise-1.6T. Choose STACK-T1A-50CM, STACK-T1A-1M, or STACK-T1A-3M to suit the measured route.

Can I use STACK-T1-50CM on a C9350?

No. STACK-T1-50CM is the Type 1 cable for C9300 and C9300X switches. The 50 cm C9350 part number is STACK-T1A-50CM.

Can a C9350 stack with a C9300X?

No. A C9350 and a C9300X cannot join the same physical StackWise stack.

Which STACK-T1A cable length do I need?

Measure each link independently and select the shortest of the 50 cm, 1 m, and 3 m options that accommodates the planned route and bend clearance. The two links can use different lengths.

Does a C9300L stack kit include the adapters and cable?

Yes. Both C9300L kits include two adapters and one cable. The original kit uses Type 3 hardware, and Kit2 uses Type 3A. Two kits supply the four adapters and two cables needed for a new two-switch ring.

Latest Articles