Compare Cisco SFP GLC modules for 1G Ethernet links where fiber type, copper handoff, reach, wavelength, connector, DOM support, temperature range, and device compatibility determine the right transceiver. Find GLC-SX-MMD, GLC-LH-SMD, GLC-ZX-SM, GLC-T, GLC-TE, and related Cisco Gigabit SFP options for switches, routers, firewalls, industrial platforms, uplink upgrades, spares, and troubleshooting replacements.
Showing all 7 results
1000BASE-EX SFP – 40km SMF – DOM
1000BASE-LX/LH SFP – 10km SMF / 550m MMF – DOM
1000BASE-LX/LH 1310nm – 10 km SMF / 550 m MMF – Industrial Temperature SFP
1G SX SFP – 550m MMF – Industrial Temp
1000BASE-SX SFP – MMF 850nm – DOM
1000BASE-T SFP – RJ-45 Cat5 Copper – 100m Reach
1000BASE-ZX SFP – 70km SMF – EXT DOM
A Cisco SFP GLC module is a 1 Gigabit Ethernet transceiver for supported Cisco SFP ports. Buyers use GLC modules for access switch uplinks, router handoffs, firewall links, industrial links, spare replacement, and copper-to-fiber connectivity.
Choose GLC-SX-MMD for short multimode fiber, GLC-LH-SMD for longer single-mode or supported multimode links, and GLC-T or GLC-TE for RJ-45 copper Gigabit Ethernet. The installed cabling usually decides the correct SKU.
GLC-SX-MMD is for 1000BASE-SX short-reach multimode fiber, while GLC-LH-SMD is for 1000BASE-LX/LH longer-reach links. Check fiber type, distance, patch cable, optical budget, and Cisco device support before choosing.
GLC-T and GLC-TE are copper 1000BASE-T SFP options, but platform support and temperature ratings can differ. GLC-TE is often considered where extended operating temperature support is required, subject to device compatibility.
Yes, GLC-SX-MMD is commonly selected when digital optical monitoring is needed for short-reach multimode links. DOM helps check transmit power, receive power, temperature, and link health during troubleshooting.
Cisco 1000BASE-SX GLC modules are commonly used for short multimode fiber links, with reach depending on fiber type and quality. Cisco lists GLC-SX-MM operation on multimode spans up to 550 meters.
Some Cisco SFP+ ports support 1G SFP operation, but this is platform- and software-dependent. Check the Cisco compatibility matrix and device release notes before installing a GLC module in a 10G-capable port.
Many optical GLC modules use duplex LC fiber connectors, while copper GLC modules use RJ-45. Verify connector type, multimode or single-mode fiber, duplex polarity, cable category, and patch-panel condition before installation.
Common causes include wrong GLC SKU, dirty LC connectors, unsupported SFP port, bad RJ-45 cabling, mismatched fiber type, incorrect speed setting, weak receive power, old software, or exceeding the intended 1G link distance.
Verify exact GLC SKU, Cisco device model, port support, fiber type, copper or optical need, reach, connector, DOM support, temperature range, compatibility matrix status, warranty, condition, and lead time before purchasing.
Cisco SFP GLC Modules are commonly purchased for Gigabit Ethernet links where the main decision comes down to media type, link distance, and platform compatibility. This category brings together widely used Cisco GLC transceivers for copper, multimode fiber, and single-mode fiber deployments, making it easier to compare options such as GLC-T, GLC-SX-MMD, GLC-LH-SMD, GLC-EX-SMD, and GLC-ZX-SMD before ordering. It is especially useful for buyers expanding existing Cisco switch or router ports, replacing failed optics, or planning spare inventory for installed networks.
Notifications