If my 1-meter stack cable fails to link switches, how should I start troubleshooting?

Confirm both ends are fully seated, examine the cable for visible damage, and swap with another link cord if possible. Check for correct port usage.

What’s included in the packaging when I order a 1m stack connector?

Typically, you receive the 1m stack cord and sometimes a protective sleeve. Always verify package contents for completeness.

How is a 1m stack cord different from a short (50cm) or long (3m) stack link?

A 1m link provides moderate reach—longer than a half-meter, but less excess cabling than a 3m cord, reducing clutter.

Are compatible non-Cisco stack cords available for 1m applications?

Though other cables might work physically, Cisco recommends their original stacking cables for maximum reliability.

What rack configurations most benefit from a 1-meter stacking cable?

Best for switches installed two or three rack units apart or on opposite sides of cable organizers.

Are there precautions to observe during installation of a 1m interconnect?

Always disconnect power when possible, and handle the cable gently to avoid internal conductor damage.

Is this link cord compatible with all stacking ports on Cisco 9200 models?

Most Cisco 9200 Series switches with StackWise-320 stacking support the 1m cord—consult your switch guide.

How can I verify correct operation of my 1m stacking cable?

Check CLI output with `show switch stack-ports` and look for a stable green LED on stack ports.

What’s the recommended path for routing a 1m stack link in network cabinets?

Route horizontally or vertically along cable management arms to avoid tight bends or tangles.

Will using different cable lengths affect stack topology?

Different cable lengths can be used if all cables are genuine and installed securely.

Is a specific software version needed for this interconnect?

Stacking features require minimum switch firmware, but the cable itself is passive.

How does a 1m stack cable maintain signal quality?

It uses shielded conductors to minimize interference, ensuring clear signals at moderate distances.

What visual signs suggest a 1m stack cable is faulty?

A blinking or amber port LED, or repeated stack reformation events, can indicate a problem.

Can I form ring topologies with multiple 1-meter cables?

Yes, multiple cables of any supported length can be used to create ring stacks for redundancy.

Where can I find Cisco’s guidelines for installing a 1m stack cord?

Refer to the Catalyst 9200 hardware installation guide or Cisco’s official website.

How do I spot a counterfeit 1m stack cable?

Check for Cisco branding, part numbers, and compare to images on Cisco’s support site.

If my 1m stacking link is unstable, what should I do?

Swap with a new cable, clean port contacts gently, and ensure correct routing.

Can I unplug the 1m stack connector with the switch running?

Hot-swapping is supported, but it may cause stack reconfiguration—check Cisco best practices.

How do I claim warranty service for a 1m stack cord?

Contact Cisco support or your reseller with your proof of purchase.

What is the best way to store 1m stack connectors when not in use?

Keep them loosely coiled, dry, and away from sharp objects.

STACK-T4-1M – 1 m stacking cable – Cisco Catalyst 9200

Name: STACK-T4-1M Price & DataSheet - Cisco Cables Accessories
SKU: STACK-T4-1M
Price: 74.26 USD
Availability: InStock
Rating: 5.00 (11 reviews)

Brand:

Cisco

Category:

Cisco Cables Accessories

Availability: In Stock Model:

STACK-T4-1M

Rated 5.00 out of 5 based on 11 customer ratings

(11 customer reviews)

Questions

0/mo Solds

~~List Price: $976~~ $74.26

100% Genuine
Original, factory-authenticated
S/N Verifiable
Verified by official serial-check

Condition New Factory Sealed Related Quantity

Available on backorder

Trusted & Secure Payments

Shipping Express Shipping 2-6 Days, via DHL, FedEx, UPS, etc. Packaging weight and dimensions included:

Weight	5.3 kg
Dimensions	41 × 43 × 15 cm

Certified Expertise for Project Delivery

CCIE · JNCIE · NSE7 · ACDX · HPE · Dell Server/AI Expert

Stable Global Supply Chain for Thriving Businesses.

$3,000,000 Inventory
Certified Cisco Partner ships
Collaborating with FedEx, UPS, DHL

Free Expert Support from Planning to Deployment

Assistance with product selection and network solution design
Configuration guidance and best-practice recommendations
Troubleshooting support provided by CCIE-level technical experts

Established Global IT Distributor

With over a decade of industry experience, we are a certified Cisco Partner delivering genuine enterprise networking hardware and trusted services to system integrators, ISPs, and enterprises worldwide.

STACK-T4-1M Description

STACK-T4-1M is the 1 m Cisco StackWise Type-3 data-stack cable (also known as the 1 m Type-3 stacking cable or 1 m StackWise-80/160 cable), designed to link Catalyst 9200 and 9200L switches in a StackWise-80 or StackWise-160 stack. Featuring rugged PVC jacket, proprietary Cisco copper connectors, and a ±5 mm length tolerance, it ensures reliable inter-switch connectivity over longer spans where the default 0.5 m cable is insufficient.

Model Meaning

Model Segment	Meaning
STACK	Cisco StackWise stacking cable
T4	Type-3 data-stack cable
1M	1 m (meter) cable length

Product Key Feature Bullets

1 m Type-3 stacking cable for Cisco StackWise-80/160 deployments.
Optional accessory; complements default 0.5 m STACK-T4-50CM cable.
Spare-part SKU STACK-T4-1M= for field replacement.
Compatible with both C9200-STACK-KIT and C9200L-STACK-KIT.
Rugged PVC jacket, copper conductor; operating –5 °C to 45 °C, storage –40 °C to 70 °C.
Covered by Cisco Enhanced Limited Lifetime Hardware Warranty.

Specifications

Parameter	Value	Parameter	Value
Product SKU	STACK-T4-1M	Spare SKU	STACK-T4-1M=
Cable Length	1 m	Cable Type	StackWise Type-3 data-stack copper
Default with Kits	Optional	Compatible Kits	C9200-STACK-KIT, C9200L-STACK-KIT
Connector Type	Cisco proprietary copper	FRU	Yes
Hot-Swappable	Yes	Jacket Material	PVC
Conductor	Copper	Length Tolerance	±5 mm
Bend Radius, Min	10 mm	Cable Color	Light blue
Operating Temp.	–5 °C to 45 °C	Storage Temp.	–40 °C to 70 °C
Weight	~0.08 kg	Packaging	Polybag
Compliance	RoHS, WEEE	Warranty	Enhanced Limited Lifetime

Get More Information

Discover unbeatable prices and fast shipping for the STACK-T4-1M Access the detailed STACK-T4-1M datasheet and ensure you’re getting the best deal with our reliable delivery service. Need assistance? Our free live chat support is here to help. For more information about the product and pricing, contact us via Live chat or email us at [email protected]

Quality Certifications

Customer Reviews

Write A Review

5.0

Rated 5.00 out of 5

(11 reviews)

5 Stars

11

4 Stars

0

3 Stars

0

2 Stars

0

1 Stars

0

Lucas Bishop

Posted on 25/07/2025

Verified Buyer

Rated 5 out of 5

5.0

The shipment arrived on schedule. Good execution.

Betsy Braddock

Posted on 18/05/2025

Verified Buyer

Rated 5 out of 5

5.0

Focused service. Clear communication.

Network Lead

Posted on 22/03/2025

Verified Buyer

Rated 5 out of 5

5.0

Hard to find these in stock sometimes. Thanks for having them.

Supply Chain

Posted on 12/01/2025

Verified Buyer

Rated 5 out of 5

5.0

Bulk pack arrived safely. Good palletizing.

Faith Ward

Posted on 16/05/2024

Verified Buyer

Rated 5 out of 5

5.0

Perfect length for our setup, cable feels durable.

Questions & Answers

If my 1-meter stack cable fails to link switches, how should I start troubleshooting?
Confirm both ends are fully seated, examine the cable for visible damage, and swap with another link cord if possible. Check for correct port usage.
What’s included in the packaging when I order a 1m stack connector?
Typically, you receive the 1m stack cord and sometimes a protective sleeve. Always verify package contents for completeness.
How is a 1m stack cord different from a short (50cm) or long (3m) stack link?
A 1m link provides moderate reach—longer than a half-meter, but less excess cabling than a 3m cord, reducing clutter.
Are compatible non-Cisco stack cords available for 1m applications?
Though other cables might work physically, Cisco recommends their original stacking cables for maximum reliability.
What rack configurations most benefit from a 1-meter stacking cable?
Best for switches installed two or three rack units apart or on opposite sides of cable organizers.
Are there precautions to observe during installation of a 1m interconnect?
Always disconnect power when possible, and handle the cable gently to avoid internal conductor damage.
Is this link cord compatible with all stacking ports on Cisco 9200 models?
Most Cisco 9200 Series switches with StackWise-320 stacking support the 1m cord—consult your switch guide.
How can I verify correct operation of my 1m stacking cable?
Check CLI output with `show switch stack-ports` and look for a stable green LED on stack ports.
What’s the recommended path for routing a 1m stack link in network cabinets?
Route horizontally or vertically along cable management arms to avoid tight bends or tangles.
Will using different cable lengths affect stack topology?
Different cable lengths can be used if all cables are genuine and installed securely.
Is a specific software version needed for this interconnect?
Stacking features require minimum switch firmware, but the cable itself is passive.
How does a 1m stack cable maintain signal quality?
It uses shielded conductors to minimize interference, ensuring clear signals at moderate distances.
What visual signs suggest a 1m stack cable is faulty?
A blinking or amber port LED, or repeated stack reformation events, can indicate a problem.
Can I form ring topologies with multiple 1-meter cables?
Yes, multiple cables of any supported length can be used to create ring stacks for redundancy.
Where can I find Cisco’s guidelines for installing a 1m stack cord?
Refer to the Catalyst 9200 hardware installation guide or Cisco’s official website.
How do I spot a counterfeit 1m stack cable?
Check for Cisco branding, part numbers, and compare to images on Cisco’s support site.
If my 1m stacking link is unstable, what should I do?
Swap with a new cable, clean port contacts gently, and ensure correct routing.
Can I unplug the 1m stack connector with the switch running?
Hot-swapping is supported, but it may cause stack reconfiguration—check Cisco best practices.
How do I claim warranty service for a 1m stack cord?
Contact Cisco support or your reseller with your proof of purchase.
What is the best way to store 1m stack connectors when not in use?
Keep them loosely coiled, dry, and away from sharp objects.

Warranty

100% Low Price Guarantee:

Layer23-switch.com provides high-quality products at low wholesale prices

100% Quality Assurance:

All items are ORIGINAL and GENUINE only.
Item conditions are "New Sealed" or "Used / Refurbished".
Used & refurbished items are fully tested with good conditions by Cisco-certified Engineers.

Free CCIE Technical Support:

Our FREE Cisco CCIE Expert Consultancy Support is over the phone, by chat, by email or by login remotely.

100% Money Back Guarantee:

You can contact our customer service team to exchange or return any product that you bought from us.

Standard Services

Personalized Service, Superior Product Maintenance for Ultimate Satisfaction.

Projects and Technical Support
Easy Purchasing Supply
Product Lifecycle Protection
Exclusive F3 Team Support

Customized Support for Your Needs with CCIE, HCIE, HPE ASE, etc.

Shipping

Resources Downloads

STACK-T4-1M Datasheet

Product Tag

1M C9200 C9200L stack

STACK-T4-1M – 1 m stacking cable – Cisco Catalyst 9200

STACK-T4-1M Description

Model Meaning

Product Key Feature Bullets

Specifications

Get More Information

Quality Certifications

Customer Reviews

Questions & Answers

If my 1-meter stack cable fails to link switches, how should I start troubleshooting?

What’s included in the packaging when I order a 1m stack connector?

How is a 1m stack cord different from a short (50cm) or long (3m) stack link?

Are compatible non-Cisco stack cords available for 1m applications?

What rack configurations most benefit from a 1-meter stacking cable?

Are there precautions to observe during installation of a 1m interconnect?

Is this link cord compatible with all stacking ports on Cisco 9200 models?

How can I verify correct operation of my 1m stacking cable?

What’s the recommended path for routing a 1m stack link in network cabinets?

Will using different cable lengths affect stack topology?

Is a specific software version needed for this interconnect?

How does a 1m stack cable maintain signal quality?

What visual signs suggest a 1m stack cable is faulty?

Can I form ring topologies with multiple 1-meter cables?

Where can I find Cisco’s guidelines for installing a 1m stack cord?

How do I spot a counterfeit 1m stack cable?

If my 1m stacking link is unstable, what should I do?

Can I unplug the 1m stack connector with the switch running?

How do I claim warranty service for a 1m stack cord?

What is the best way to store 1m stack connectors when not in use?

Warranty

Standard Services

Resources Downloads

Product Tag

Related products

C9200L-48T-4X-E

STACK-T4-50CM

C9200-24P-E

C9200L-48P-4X-E