SFP-10G-SR-S – 10GBASE-SR SFP+ – S-Class – 400m OM4 MMF
35/mo Solds
Established Global IT Distributor
With over a decade of industry experience, we are a certified Cisco Partner delivering genuine enterprise networking hardware and trusted services to system integrators, ISPs, and enterprises worldwide.
SFP-10G-SR-S Description
SFP-10G-SR-S is a Cisco S-Class 10GBASE-SR SFP+ optical transceiver for 10 Gigabit Ethernet links over 850 nm multimode fiber. It fits short-reach MMF uplink and interconnect designs that need an S-Class SR optic with dual LC/PC connectivity, 300 m reach on OM3 fiber, 400 m reach on OM4 or OM5 fiber, commercial 0 to 70 degrees C operation, beige bail latch identification, 1W maximum power consumption, and Cisco-documented no-FCoE support for this PID.
Quick Specs
|
Parameter |
Specification |
|---|---|
|
Product ID |
SFP-10G-SR-S |
|
Product type |
10GBASE-SR S-Class SFP+ transceiver |
|
Module class |
S-Class |
|
Ethernet protocol |
10GBASE-SR |
|
Fiber type |
Multimode fiber |
|
Nominal wavelength |
850 nm |
|
Reach on OM3 MMF |
300 m |
|
Reach on OM4 or OM5 MMF |
400 m |
|
Connector |
Dual LC/PC |
|
FCoE support |
Not supported |
|
Maximum power consumption |
1W |
|
Operating temperature class |
Commercial 0 to 70 degrees C |
Application Scenarios
Specify SFP-10G-SR-S when the approved Cisco materials call for an S-Class 10GBASE-SR SFP+ optic on short multimode fiber runs rather than the standard SR PID.
Keep this optic in 10G Ethernet designs where FCoE is outside the service requirement. Cisco marks the S-Class SR PID with no FCoE support, so converged storage traffic needs a separate approved optic review.
Store SFP-10G-SR-S apart from SFP-10G-SR, SFP-10G-SR-X, and SFP-10G-SR-I. The shared 850 nm reach class does not remove the ordering difference between S-Class, extended-temperature, and industrial SR variants.
Product Comparison
|
Parameter |
SFP-10G-SR-S |
SFP-10G-SR-I | ||
|---|---|---|---|---|
|
Product type |
10GBASE-SR S-Class SFP+ transceiver |
10GBASE-SR SFP+ transceiver |
Extended-temperature multirate SR SFP+ transceiver |
Industrial-temperature multirate SR SFP+ transceiver |
|
Ordering description |
10GBASE-SR SFP+ Module for MMF S-Class |
10GBASE-SR SFP+ Module for MMF |
Multirate 10GBASE-SR, 10GBASE-SW and OTU2e SFP+ Module for MMF, extended temperature range |
Multirate 10GBASE-SR, 10GBASE-SW and OTU2/2e SFP+ Module for MMF, industrial temperature range |
|
Module position |
S-Class SR listing |
Standard SR listing |
Extended-temperature SR listing |
Industrial SR listing |
|
Supported media |
MMF |
MMF |
MMF |
MMF |
|
Nominal wavelength |
850 nm |
850 nm |
850 nm |
850 nm |
|
OM3 reach |
300 m |
300 m |
300 m |
300 m |
|
OM4 or OM5 reach |
400 m |
400 m |
400 m |
400 m |
|
Protocol scope |
10GBASE-SR with no FCoE support |
10GBASE-SR |
10GBASE-SR, 10GBASE-SW and OTU2e |
10GBASE-SR, 10GBASE-SW, OTU2/2e and CPRI options |
|
Operating temperature class |
Commercial |
Commercial |
Extended |
Industrial |
|
Maximum power consumption |
1W |
1W |
1W |
1W |
|
Bail latch color |
Beige |
Beige |
Beige |
Beige |
- In a SFP-10G-SR-S vs SFP-10G-SR comparison, the cabling table shows the same 850 nm MMF SR reach, while SFP-10G-SR-S is the S-Class PID and carries Cisco’s no-FCoE support note.
- The SFP-10G-SR-S difference from SFP-10G-SR-X is the operating and protocol scope: SR-S is commercial-temperature S-Class SR, while SR-X is Cisco’s extended-temperature multirate SR/SW/OTU2e listing.
- SFP-10G-SR-S vs SFP-10G-SR-I is a comparison between Cisco’s commercial S-Class SR optic and the industrial-temperature SR listing with CPRI options.
- For which model to choose, align the order with the required PID class, FCoE need, temperature class, multimode cable grade, and Cisco host-compatibility result.
Selection Guide
1. Lock the order to the SR-S identifier
The quote evidence and receiving label should show the exact SFP-10G-SR-S PID. If the request only says 10G SR, clarify whether the standard SR optic or the S-Class SR-S line is intended before purchase.
2. Keep storage convergence out of scope
Cisco’s no-FCoE statement is a hard filter for this SKU. A link carrying FCoE should be reviewed against another Cisco-approved optic instead of treating SR-S as a general SR substitute.
3. Use cable reach as the second filter
Approve the multimode path only when the planned distance fits Cisco’s SR table: 300 m on OM3 or 400 m on OM4 or OM5. A longer route needs a different optical design.
4. Separate environmental variants during review
Extended-temperature requirements point to SFP-10G-SR-X, while industrial or CPRI requirements point to SFP-10G-SR-I. Keep SFP-10G-SR-S as the commercial S-Class SR option after Cisco host support is verified.
Ordering Checklist
|
Check Item |
What to Confirm |
Procurement Risk Controlled |
|---|---|---|
|
FCoE design check |
The planned link is 10GBASE-SR Ethernet without an FCoE requirement |
Keeps the order inside Cisco’s S-Class SR support boundary |
|
Device support evidence |
Cisco compatibility documentation or a Cisco platform release note covers the target host and software |
Avoids approving the optic only because the port is physically SFP+ |
|
MMF distance plan |
The fiber run uses supported multimode fiber and stays within the OM3 300 m or OM4/OM5 400 m limits |
Prevents an SR optic from being used on an unsupported cable grade or distance |
|
LC patch-cord polish |
Patch cords use LC/PC or LC/UPC connectors and exclude APC ends |
Reduces connector mismatch risk during installation testing |
|
Commercial-temperature fit |
Site temperature requirements fit Cisco’s commercial operating class |
Keeps extended-temperature or industrial requirements from being filled with SR-S |
Specifications
| Parameter | Specification | Parameter | Specification |
|---|---|---|---|
| Product ID | SFP-10G-SR-S | Product type | 10GBASE-SR S-Class SFP+ transceiver |
| Ordering description | 10GBASE-SR SFP+ Module for MMF S-Class | Module class | S-Class |
| Ethernet protocol | 10GBASE-SR | FCoE support | Not supported |
| Fiber type | Multimode fiber | Nominal wavelength | 850 nm |
| Transmit and receive wavelength range | 840 to 860 nm | Connector | Dual LC/PC |
| FDDI-grade MMF reach | 26 m with 62.5 micron 160 MHz*km fiber | OM1 MMF reach | 33 m with 62.5 micron 200 MHz*km fiber |
| 400 MHz*km MMF reach | 66 m with 50.0 micron fiber | OM2 MMF reach | 82 m with 50.0 micron 500 MHz*km fiber |
| OM3 MMF reach | 300 m with 50.0 micron 2000 MHz*km fiber | OM4 MMF reach | 400 m with 50.0 micron 4700 MHz*km fiber |
| OM5 MMF reach | 400 m with 50.0 micron 4700 MHz*km fiber | Minimum cabling distance | 2 m |
| Transmit power range | -1.2 to -7.3 dBm | Receive power range | -1.0 to -9.9 dBm |
| Bail latch color | Beige | Maximum power consumption | 1W |
| Operating temperature class | Commercial | Commercial operating temperature | 0 to 70 degrees C |
| Storage temperature range | -40 to 85 degrees C | SFP+ connector dimensions | 8.5 x 13.4 x 56.5 mm |
| SFP+ connector weight | 75 grams or less | C9200L support example | C9200L Multigigabit Ethernet 10G uplink release notes list SFP-10G-SR-S |
| Platform support boundary | Cisco compatibility documentation required for exact host and software support | Standard warranty | 5 years |
Get More Information
Need pricing, stock, or shipping details for the SFP-10G-SR-S ? Layer23-Switch can help you check current availability, lead time, and delivery options for this. Send us the part number, quantity, and destination country via live chat or email sales@layer23-switch.com for a fast quotation.
Quality Certifications
Customer Reviews
Questions & Answers
-
What is Cisco SFP-10G-SR-S used for?
-
How far can SFP-10G-SR-S reach?
-
Is SFP-10G-SR-S single-mode or multimode?
-
How is SFP-10G-SR-S different from SFP-10G-SR?
-
Does SFP-10G-SR-S support FCoE?
-
What connector does SFP-10G-SR-S use?
-
Can SFP-10G-SR-S connect to SFP-10G-SR?
-
When is SFP-10G-SR-S the wrong SKU?
Warranty
Layer23-Switch.com offers genuine, high-quality ICT products at competitive wholesale prices—ensuring exceptional value without compromising quality.
All items are brand new, original, and factory-sealed.
Upon request, each unit can be fully tested and verified by a Cisco CCIE-certified engineer to ensure perfect working condition before shipment.
Our Cisco CCIE-certified experts provide free professional support via phone, email, online chat, or remote login—helping you deploy and troubleshoot with confidence.
If you are not satisfied with your purchase, you may request an exchange or full refund. Our customer service team will guide you through the return process quickly and smoothly. Visit Return Policy page for more information.
We support multiple secure payment and logistics options, backed by industry-leading verification:
Visit How to Pay page for more information
Extended, Worry-Free Warranty Coverage Factory New Sealed Enterprise Hardware:
· 3 Years Factory New Sealed
Visit Warranty Policy page for more information
Verify, plan, and comparewith confidence
Use practical tools to check device details, review lifecyclemilestones, and compare hardware before you buy.
Standard Services
Personalized Service, Superior Product Maintenance for Ultimate Satisfaction.
- Projects and Technical Support
- Easy Purchasing Supply
- Product Lifecycle Protection
- Exclusive F3 Team Support
Customized Support for Your Needs with CCIE, HCIE, HPE ASE, etc.
Quality felt premium. No corners cut anywhere in the product or packaging.
If you want a vendor that consistently delivers, Layer23 is it.
We have a standing order arrangement with Layer23. It works perfectly.
Pricing is very fair for genuine units. Shipping was quick and the invoice detail was exactly what our finance department needed.
Genuine Cisco optics. Essential for our strict compliance requirements. Appreciate the fast turnaround on the quote.